Honey Well Dream Weaver™ Sleep Fan User Manual

Honey Well Dream Weaver™ Sleep Fan User Manual

IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE THESE SAFETY INSTRUCTIONS BEFORE USING THIS FAN
When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following: FOR US MODELS ONLY – This product employs overload protection (fuse). A blown fuse indicates an overload or short-circuit situation. If the fuse blows, unplug the product from the outlet. Replace the fuse as per the user servicing instructions (follow product marking for proper fuse rating) and check the product. If the replacement fuse blows, a short-circuit may be present and the product should be discarded or returned to an authorized service facility for examination and/or repair.

1.  Use this fan only as described in this manual. Other use not recommended as it may cause fire, electric shock or injury to persons.
2. This product is intended for household use ONLY and not for commercial, industrial or outdoor use.
3.  To protect against electric shock, do not place fan in window, immerse unit, plug or cord in water or spray with liquids.
4.  This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of shock, this plug is intended to fit only one way in a polarized outlet. If the plug does not fit fully in the outlet, reverse
   the plug. If it still does not fit, contact a qualified electrician. DO NOT attempt to
   defeat this safety feature.
5. Close supervision is necessary when any appliance is used by or near children.

FUSED SAFETY PLUG – FOR US ONLY

This fan features a fused safety plug which is designed to cut off electric current to the fan if an electrical fault occurs. Please see below for more information on how to properly use your fan and replace the safety plug fuse, if needed.
USER SERVICING INSTRUCTIONS

•  If your fan loses power and you suspect that the fuse on your fan has blown, grasp plug and remove from the receptacle or other outlet device. Do not unplug by pulling on cord.
• Slide fuse cover, located on the top of the plug, towards the prongs of the plug. (Fig. 1)
•  Carefully remove the blown fuse and snap a new fuse into place.To Reduce the Risk of Fire, replace fuse only with 2.5 Amp, 125 volt fuse. Fully close the fuse door by sliding back into place. (Fig. 2) Discard the blown fuse. The plug should now be ready for normal use.
• To Reduce the Risk of Fire, do not replace attached plug.Contains a safety device (fuse) that should not be removed.Discard product if the attached plug is damaged.
•  If you need further information on how or when to replace the fuse in the safety plug, please contact Kaz Consumer Relations Department by visiting our website at www.honeywellpluggedin.com/fans or calling
  1-800-477-0457.

ASSEMBLY INSTRUCTIONS

A.BASE ASSEMBLY

• Remove 2 thumb screws from the base and set aside. Align the front and back base pieces and gently push until pieces snap securely together (Fig. 3).

B. SECURING THE TOWER FAN TO THE BASE

• At the base of the housing, remove the locking nut and set aside.
• Carefully lift the fan housing (Fig. 4) and place the power cord through the center of the base.
• Lower the fan housing into the base (Fig. 4), align the back of the fan with the back of the base. Gently rotate the fan housing until it is seated in the base. (Fig. 5).
•  Take the locking nut and place power cord through the locking nut (Fig 4) bringing locking nut up inside the base, (Fig. 5) screw the locking nut onto the fan housing turning clockwise until fully tightened and an
  audible ratcheting is heard.

D. SECURING THE CORD INSIDE THE BASE

• Gently place the fan on its side, pressing the cord securely into cord guides (Fig. 6) along the inside of fan base, exiting through the notched opening (Fig. 6) ensuring a flat and stable base for the fan.
•  Place 2 thumb screws into the the base for added stability (Fig. 7).
•  Return the tower fan to its upright position.

Note: Do not operate the tower fan unless it is in its proper,upright position.

ASSEMBLY INSTRUCTIONS

REMOTE CONTROL BATTERY INSTALLATION/REPLACEMENT INSTRUCTIONS

• A. Remove battery door by sliding downward in direction of arrow (Fig. 8).
• B. Insert 2 AAA batteries into the remote following the directional guides in the recessed slots. Batteries are included.
• C. Replace battery door by sliding upward opposite of arrow direction until door snaps in place.

NOTE: DO NOT MIX OLD AND NEW BATTERIES. DO NOT MIX ALKALINE,STANDARD (CARBON-ZINC) OR RECHARGEABLE (NICKEL-CADMIUM) BATTERIES.SEE RECYCLERS IN YOUR AREA FOR PROPER DISPOSAL OF BATTERIES.

FAN OPERATION

ON/OFF

To turn fan on, press the Power button  located on the bottom center of the control panel.

SPEED CONTROL
The fan will automatically start on “Sleep” speed when initially turned on. To adjust the speed up or down, press
the Fan Speed button  repeatedly to increase level.

OSCILLATION

To activate the Oscillation feature, press the Oscillation button once. Press the Oscillation button again to turn the
Oscillation feature off.

TIMER
Choose from 1, 2, 4, or 8 hour settings by performing the following function:

•  1 hour: Press the Timer button ( ) once.
•  2 hours: Press the Timer button twice.
•  4 hours: Press the Timer button a third time.
•  8 hours: Press the Timer button a fourth time.

Press the Timer button a fifth time to turn the Timer feature off.

AUTO DIM LIGHT FEATURE
Control panel light automatically dims to 50% brightness after 15 seconds and resumes to 100% brightness when settings are changed.

CLEANING AND STORAGE

• Ensure the fan is turned off and unplugged.
• Use only a soft cloth to gently wipe the outer surfaces of the fan clean.
• To clean between the grills and fan blade area, we recommend using a pipe cleaner, flexible dust wand, vacuum cleaner or compressed air to gently remove the dust.
• To clean the rear grill use a soft dry cloth.
• DO NOT immerse the fan in water and never allow water to drip into the motor housing.
•  DO NOT use gasoline, paint thinner or other chemicals to clean the fan.
• For storage, you may leave the fan assembled and covered to protect it from dust. Store the fan in a cool, dry place.

CONSUMER RELATIONS

Mail questions or comments to: Kaz USA, Inc. Consumer Relations Dept.250 Turnpike Road Southborough, MA 01772 Please be sure to specify a model number.
NOTE: IF YOU EXPERIENCE A PROBLEM, PLEASE CONTACT CONSUMER RELATIONS FIRST OR SEE YOUR WARRANTY.DO NOT RETURN TO THE ORIGINAL PLACE OF PURCHASE. DO NOT ATTEMPT TO OPEN THE MOTOR HOUSING YOURSELF, DOING SO MAY VOID YOUR WARRANTY AND CAUSE DAMAGE TO THE FAN OR PERSONAL INJURY.

1 YEAR LIMITED WARRANTY

You should first read all instructions before attempting to use this product.

• A. This 1 year limited warranty applies to repair or replacement of product found to be defective
  in material or workmanship. This warranty does not apply to damage resulting from commercial, abusive, unreasonable use or supplemental damage.
• B. At its option, Kaz will repair or replace this product if it is found to be defective in material or workmanship.
• C. This warranty does not cover damage resulting from any unauthorized attempts to repair or from any use not in accordance with the instruction manual.
• D. Return defective product to Kaz, Incorporated with a brief description of the problem. Include
  proof of purchase and a $10 US/$15.50 CAN check or money order for handling, return packing and shipping charges.

In U.S.A.:Attn: Returns Department 1 Helen Of Troy Plaza El Paso, TX 79912 USA
In Canada: Kaz Canada, Inc. Attn: Returns Department 510 Bronte Street South Milton, ON L9T 2X6
Canada Please go to www.honeywellpluggedin.com/register and register your product under the Customer Care
Center and receive product information updates and new promotional offers

DOWNLOAD LINK

https://www.honeywellstore.com/store/images/pdf/htf400-honeywell-fan-manual.pdf